Manual ISA detection

[Elmic]

Report EPS815 does not indicate voltages for each test. If you are interested in voltages in different tests, you can measure them yourself using an oscilloscope.

 

[Hristache Dan]

Report EPS815 does not indicate voltages for each test. If you are interested in voltages in different tests, you can measure them yourself using an oscilloscope.

I measured today.I understood but I wanted to see the results for the VL test.

 

[Elmic]

I meant EPS815. I hope after this measurement you will disappear questions for Potok CR-2

 

[Hristache Dan]

I saw that in Bosch EPS 815 (youtube) the VL values are not so high.

 

[Hristache Dan]

Has anyone tried Bosch piezo coding? Does the last letter of the code match the one on the injector?

 

[Matej]

Yes. It's all right

 

[saab9-5]

Always

 

[Hristache Dan]

And without coding - only with ISA detection does the last letter of the code match the one on the injector ?

 

[Hristache Dan]

Always

Please give me your email adress.

 

[Hristache Dan]

Yes. It's all right

Please give your email adress to talk.

 

[Hristache Dan]

Please give your email adress to talk.

Hello.I would like to talk about Bosch piezo but i think it s easier with WatsApp - please give me your number.Thanks.

 

[Hristache Dan]

Yes. It's all right

Hello.I would like to talk about Bosch piezo but i think it s easier with WatsApp - please give me your number.Thanks.

 

[Hristache Dan]

I meant EPS815. I hope after this measurement you will disappear questions for Potok CR-2

In the report the frequency is 400 IPM for VL, VE, LL but in TP is 1000 IPM.It is OK ?

 

[Matej]

It's ok. for isa need to do 2000

 

[Hristache Dan]

It's ok. for isa need to do 2000

Please give me your WatsApp number.

 

[Matej]

+79203408993

 

[Hristache Dan]

Hello everybody!I still believe that there is a problem with the assignment of voltages after ISA detection.I checked 4 used 0986435366 pieces with software version 1.2.1.59 and they were OK. Today we have checked 0986435360 new, equivalent to 0445116030 and the flows are too high - with 1.2.1.61 software version.As I appreciate the Potok equipment I would like to clarify this problem. If anyone has encountered this problem please say.Maybe I'm wrong somewhere.

 

[Hristache Dan]

Is it normal for a new injector 0986435360 to have this result?

 

[Сергей Пантюк]

Добрый день подскажите пожалуйста, как работает в тест-плане isa detection? Как он должен определить в автоматическом режиме? Что надо делать чтоб он начал определять? И что надо делать если не определяет? И для чего нужна галочка (detect)? И как правильно проходит кодирование форсунок БОШ? Подскажите только начинаю купил оборудование с кодированием форсунок БОШ, тестировал пьеза форсунки БОШ isa detection не прошло, стенд на нём работал около двадцати минут и понял, что тут что-то не так и кода я никакого не видел. Всем спасибо.

 

[Elmic]

Что надо делать чтоб он начал определять?

Для автоматического определения ISA необходимо взвести галочку в настройках.

И для чего нужна галочка (detect)?

Для ручной работы.

И как правильно проходит кодирование форсунок БОШ

Полностью на автомате.
Работа пьезофорсунки и определение ISA очень зависят от клапана подпора.